Making Shofars Sustainably: A Jewish Workshop in Australia
Every Rosh Hashanah, Australians hear the shofar. It carries across the parks of St Kilda, drifts off the steps of a synagogue in Toorak, and rolls down the sand at Bondi where a beachside congregation gathers at dawn with the sun barely up. The sound is now so familiar that people talk around it rather than about it. Far fewer pause to ask where the horn itself comes from, and whether the sourcing of it is something a community can be proud of.
That question sits at the centre of a workshop model taking shape in Australia: making shofars from sustainable sources. The method is simple enough to explain over a schmaltz at a community hall. Rescue horn and hardwood that have already been taken from stockyards, council depots, storm debris and roadside removals; shape them by hand; learn to blow what you have made; and put the finished instrument back into service at the next Yom Kippur and Rosh Hashanah.
Australians recognise the shape of that problem even when they don't know the vocabulary. This is a country that has spent two decades arguing over timber salvage after the Black Summer fires, that sorts green waste into kerbside collections, and that has built hundreds of community sheds where retired tradies repair whatever turns up. The same instincts — waste not, mend what you can, share the tools — transfer neatly into a workshop where the material is the message.
Why a Shofar Workshop Sits So Well in Australian Jewish Life
Roughly half of Australia's Jewish community lives in Melbourne, with smaller but long-established scenes in Sydney's Woolloomooloo, Adelaide and Perth. Community life here runs on volunteers to a degree that would astonish some American congregations, so a hands-on workshop fits the calendar perfectly. It gives people something to do together in the weeks before the High Holy Days, when committees are already juggling catering, parking, youth programmes and the seating plan for the blowing.
The Jewish tradition of the shofar is not industrial. The horn is expected to be hollowed, smoothed, sealed and finished by hand, and in many congregations the final stage is reserved for a particular group — often the women of the shule, who make the case and the strap that carry the horn on the walk to the bimah. A workshop that includes both the horn and the case-making honours that division of labour rather than skipping over it.
There is also a local reason to care about materials at this particular moment. Melbourne councils are removing large storm-damaged and dying trees from parks and street verges, and residents are being pushed to direct the resulting timber, branches and green waste into reuse rather than landfill. Horn offcuts and hardwood billets from that stream are exactly what a shofar workshop needs, and the arithmetic works: a single weekend's council removal can supply a year's worth of cases for a congregation of any size.
Sourcing the Horn Without Taking from the Wild
Ram's horn remains the halachically ideal material, and it is also the hardest to source cleanly. Much of the horn sold today arrives dried, chemically treated or drawn from supply chains that are difficult for a community to trace. Alternative materials have their own complications. Bovine horn is plentiful in Australia, though its tone differs from the ram's, and any animal not slaughtered under kosher supervision raises questions of treatment for some authorities — questions best settled with a rabbi in the room, not in a workshop brochure.
For a workshop built on a sustainability ethic, the raw material is chosen for three reasons. It has already been removed from the ecosystem or the food chain; it comes with a traceable story anyone can explain to a curious child; and it can be handled in a public community building without ethical argument. Timber offers the same principle in a different register: Victorian bushfire salvage, Queensland cyclone debris, council arborist removals and the neatly bundled branches stacked for collection in suburban laneways.
Those cleanups do double duty, and the campaign platform has published a practical guide to Jewish nature cleanup crews that explains how to organise one. A crew that clears rubbish from a park on Sunday has produced a morning's worth of rescued timber and offcuts by Sunday arvo — supply and tzedakah drawn from the same afternoon.
A word about Country. Sourcing wood in Australia is never a purely technical decision. The eucalypts and myrtles worked by makers here have long histories on this land, and the Traditional Owners who have cared for them for tens of thousands of years — Wurundjeri Woi-wurrung in the Melbourne area, and the Traditional Owners wherever else the workshop travels — deserve a place in the documentation of where material comes from and how it is used. Acknowledging that in a printed materials list costs nothing and means a great deal.
Turning a Billet into a Finished Horn
The horn arrives as a curved billet, and the first hour is the least photogenic. Horn soaks in warm water to soften the keratin, then goes into a hot bath to become workable without cracking. The core is drilled out, the inner taper is planed and rasped thin, and the whole curve is smoothed with progressively finer paper. A small bore at the narrow end and a sealed mouthpiece finish the functional side. Horn dust is an irritant that settles into lungs and onto benches, so wet sanding, dust masks and a ventilated room are non-negotiable in the workshop rules.
The finishing work on the bore is what separates a display piece from an instrument. The lip has to speak, the note has to hold, and the very first blow of the morning should not split into a wheeze. Most makers leave the last hour for blowing tests, in a circle, with the doors open to the street because a room full of beginners produces a remarkable amount of air.
The case and strap are the other half of the job. Myrtle is the traditional wood, and Australian makers are fortunate here: myrtle, Aglaia myrtifolia, has naturalised along the Queensland and New South Wales coasts, while Australian blackwood and silky oak offer local alternatives for people who want a case built from timber sourced within the state. A case that cradles the curve without pressing on it, lined so a dry horn cannot crack, and a strap that survives a long walk to the synagogue — those are the details a congregation actually notices on the morning of Rosh Hashanah.
Tools, Materials and the Shape of the Workshop Day
Workshops usually run in a community hall, a shule kitchen, a TAFE woodroom or a local men's shed, which means the equipment list is deliberately portable. Nothing in it needs a workshop of its own, and nothing should cost more than the price of a decent dinner.
Materials worth bringing or collecting
- Horn offcuts from stockyards, butcheries or pastoral culls, with any sourcing details written down
- Myrtle, blackwood or silky oak billets for cases, already cut to rough length
- Leather offcuts for straps, plus beeswax or shellac for sealing
- Sandpaper in several grades, wet-sanding sponges and food-safe epoxy for repairs
Tools and safety gear
- Hand drills, brace and bits, plus rasps and a small plane for the taper
- A kettle, a heat-safe basin and a towel for soaking and warming horn
- Dust masks, ear protection and clamps or a bench vice
- A sharp knife, a file and a set of screwdrivers for finishing and repairs
The day itself is simple. A short talk on sourcing and ethics after the first cup of tea, then two hours at the benches while the more experienced makers circulate and demonstrate the boring and tapering. Lunch is BYO, because that is how community kitchens in Australia work, and the afternoon belongs to the blowing circle, the case-making table and the steady business of sanding. Finish with a listening session, and with every participant leaving holding either a horn in progress or a case they will finish at home.
Blowing Together, and Taking the Next Step
The listening hour matters more than beginners expect. A shofar note is a sustained, breathy tone that sits somewhere between a reed and a foghorn, and the ear needs a reference before it can judge one. Workshop leaders often queue short French orchestral recordings — a few minutes of short orchestral recordings before the first long call — because the room's silence and its acoustic get sorted out while the speakers are still going. Then the circle opens, and the group works through the tekiah gedolah, the truah and the sharp broken notes that have shofar blowers half a world away nodding in recognition.
What comes out of the session is usually one or two serviceable horns for the congregation, a set of cases, and a group of people who now know what the inside of a shofar looks like. Some will continue on their own. Others will join the informal mailing list that organises the next round of cleanups, the next billet of myrtle, the next weekend in the shed.
There is room for you in the next session. If you can bring an hour of blowing tuition, a spare vice, a slab of blackwood or a pair of hands that are good with rasps, the workshop will take it. Host a table in your city, offer a bench space to a shule that has never run one, sponsor a shout of coffee and tea for the arvo break, or simply register interest and bring along a friend who has never heard a shofar blown properly. Submissions, shared plans and votes on proposals like this are what the community campaign platform was built for, and a sustainable shofar workshop has enough support in it to keep growing.
The horn on Rosh Hashanah morning will be heard by everyone in the congregation, and the sourcing of it by almost nobody. That imbalance is exactly the problem a workshop can quietly fix.